Length 3462 mm Inner width: 500 mm Outer width: 580 mm Rim height: 43 mm Total height: 200 mm Weight per pair: 141 kg Minimum width of tyres/tracks: 300 mm Load capacity per pair with an axle distance of * 1000 mm: 8500 kg * 1500 mm: 10620 kg * 2000 mm: 14000 kg For a better understanding, the total height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: total height). Optionally, the heavy-duty ramps can be designed with or without an edge; there is no price difference between the two variants. If the rails are designed without a border, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 300 mm! The ramp is secured with a chain (see pictures). This is placed on the bracket welded under the ramp and attached to a suitable fastening point on the vehicle. All heavy-duty ramps can be fitted with one of the support heads shown below – either the standard head (designation in the illustration: L), hook head (G), end head with tube (T) or end head with bearing (A).

Length 4995 mm Inner width: 300 mm Outer width: 360 mm Rim height: 29 mm Total height: 100 mm Weight per pair: 62 kg Minimum width of tyres/chains: 200 mm Load capacity per pair with an axle distance of * 1000 mm: 940 kg * 1250 mm: 1000 kg * 1500 mm: 1070 kg For a better understanding, the overall height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: overall height). Optionally, the heavy-duty ramp can be supplied with or without a rim; there is no price difference between the two variants. If the rails are designed without a rim, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 200 mm! The ramp is secured by means of an aluminium bracket (see picture) that can be hooked between the tail lift and the floor of a trailer. The clamp can be flexibly pushed in and out sideways under the ramp rail. The clamp is secured against unintentional slipping out with two plastic caps. All heavy-duty ramps are available with one of the support heads shown below – either the standard head (designation in the figure: L), hook head (G), end head with tube (T) or end head with bearing (A).

Length 3962 mm Inner width: 500 mm Outer width: 580 mm Rim height: 43 mm Overall height: 200 mm Weight per pair: 161 kg Minimum width of tyres/chains: 300 mm Load capacity per pair with an axle distance of * 1000 mm: 7080 kg * 1500 mm: 8500 kg * 2000 mm: 10620 kg For a better understanding, the total height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: total height). Optionally, the heavy-duty ramps can be supplied with or without an edge; there is no price difference between the two variants. If the rails are designed without a border, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 300 mm! The ramp is secured with a chain (see pictures). This is placed on the bracket welded under the ramp and attached to a suitable fastening point on the vehicle. All heavy-duty ramps can be fitted with one of the support heads shown below – either the standard head (designation in the illustration: L), hook head (G), end head with tube (T) or end head with bearing (A).

Length: 3485 mm Inner width: 340 mm Outer width: 400 mm Rim height: 39.5 mm Total height: 125 mm Weight per pair: 64 kg Minimum tyre/track width: 200 mm Load capacity per pair with an axle distance of * 1000 mm: 2750 kg * 1500 mm: 3435 kg * 2000 mm: 4580 kg For a better understanding, the overall height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: overall height). Optionally, the heavy-duty ramp can be supplied with or without a lip; there is no price difference between the two variants. If the rails are designed without a lip, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 200 mm! The ramp is attached by means of an aluminium bracket (see picture) that can be hooked between the tail lift and the floor of a trailer. The clamp can be flexibly slid in and out under the ramp rail. Two plastic caps prevent the clamp from slipping out unintentionally. All heavy-duty ramps are available with one of the support heads shown below – either the standard head (designation in the figure: L), hook head (G), end head with tube (T) or end head with bearing (A).

Length 3495 mm Inner width: 440 mm Outer width: 500 mm Edge height: 29 mm Total height: 65 mm Weight per pair: 50 kg Minimum tyre/track width: 300 mm Load capacity per pair with an axle distance of * 1000 mm: 800 kg * 1250 mm: 880 kg * 1500 mm: 1000 kg For a better understanding, the total height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: total height). Optionally, the heavy-duty ramp can be supplied with or without a lip; there is no price difference between the two variants. If the rails are designed without a lip, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 300 mm! The ramp is attached by means of an aluminium bracket (see picture) that can be hooked between the tail lift and the floor of a trailer. The clamp can be flexibly pushed in and out under the ramp rail. It is secured against unintentional slipping out with two plastic caps. All heavy-duty ramps are available with one of the support heads shown below – either the standard head (designation in the figure: L), hook head (G), end head with tube (T) or end head with bearing (A).

Length 4495 mm Inner width: 340 mm Outer width: 400 mm Rim height: 29 mm Total height: 100 mm Weight per pair: 60 kg Minimum width of tyres/chains: 200 mm Load capacity per pair with an axle distance of * 1000 mm: 1070 kg * 1250 mm: 1160 kg * 1500 mm: 1250 kg For a better understanding, the total height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: total height). Optionally, the heavy-duty ramp can be supplied with or without a lip; there is no price difference between the two variants. If the rails are designed without a lip, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 300 mm! The ramp is attached by means of an aluminium bracket (see picture) that can be hooked between the tail lift and the floor of a trailer. The clamp can be flexibly pushed in and out under the ramp rail. It is secured against unintentional slipping out with two plastic caps. All heavy-duty ramps are available with one of the support heads shown below – either the standard head (designation in the figure: L), hook head (G), end head with tube (T) or end head with bearing (A).

Length 2995 mm Inner width: 240 mm Outer width: 300 mm Rim height: 29 mm Total height: 65 mm Weight per pair: 32 kg Minimum tyre/track width: 150 mm Load capacity per pair with an axle distance of * 1000 mm: 1000 kg * 1250 mm: 1140 kg * 1500 mm: 1330 kg For a better understanding, the total height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: total height). Optionally, the heavy-duty ramp can be supplied with or without a lip; there is no price difference between the two variants. If the rails are designed without a lip, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 150 mm! The ramp is attached by means of an aluminium bracket (see picture) that can be hooked between the tail lift and the floor of a trailer. The clamp can be slid in and out under the ramp rail. It is secured against unintentional slipping out with two plastic caps. All heavy-duty ramps are available with one of the support heads shown below – either the standard head (designation in the figure: L), hook head (G), end head with tube (T) or end head with bearing (A).

Length 1995 mm Inner width: 240 mm Outer width: 300 mm Rim height: 29 mm Total height: 75 mm Weight per pair: 28 kg Minimum tyre/track width: 150 mm Load capacity per pair with an axle distance of * 1000 mm: 3500 kg * 1250 mm: 3500 kg * 1500 mm: 3500 kg For a better understanding, the total height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: total height). Optionally, the heavy-duty ramp can be supplied with or without a lip; there is no price difference between the two variants. If the rails are designed without a lip, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 150 mm! The ramp is attached by means of an aluminium bracket (see picture) that can be hooked between the tail lift and the floor of a trailer. The clamp can be flexibly pushed in and out sideways under the ramp rail. The clamp is secured against unintentional slipping out with two plastic caps. All heavy-duty ramps are available with one of the support heads shown below – either the standard head (designation in the figure: L), hook head (G), end head with tube (T) or end head with bearing (A).  

Length: 4485 mm Inner width: 300 mm Outer width: 360 mm Rim height: 39.5 mm Total height: 125 mm Weight per pair: 74 kg Minimum tyre/track width: 200 mm Load capacity per pair with an axle distance of * 1000 mm: 1965 kg * 1500 mm: 2290 kg * 2000 mm: 2750 kg For a better understanding, the total height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: total height). Optionally, the heavy-duty ramp can be supplied with or without a lip; there is no price difference between the two variants. If the rails are designed without a lip, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 200 mm! The ramp is attached by means of an aluminium bracket (see picture) that can be hooked between the tail lift and the floor of a trailer. The clamp can be flexibly slid in and out under the ramp rail. Two plastic caps prevent the clamp from slipping out unintentionally. All heavy-duty ramps are available with one of the support heads shown below – either the standard head (designation in the figure: L), hook head (G), end head with tube (T) or end head with bearing (A).

Length: 4462 mm Inner width: 450 mm Outer width: 510 mm Rim height: 43 mm Total height: 185 mm Weight per pair: 142 kg Minimum tyre/track width: 200 mm Load capacity per pair with an axle distance of * 1000 mm: 5070 kg * 1500 mm: 5910 kg * 2000 mm: 7100 kg For a better understanding, the overall height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: overall height). Optionally, the heavy-duty ramp can be ordered with or without a rim. The special price for this ramp model is only valid for the version with a rim, and the rimless version is subject to a surcharge. If the rails are designed without a rim, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 200 mm! The ramp is secured with a chain (see pictures). This is placed on the bracket welded under the ramp and attached to a suitable fastening point on the vehicle. All heavy-duty ramps can be fitted with one of the support heads shown below – either the standard head (designation in the illustration: L), hook head (G), end head with tube (T) or end head with bearing (A).

Length 4462 mm Inner width: 500 mm Outer width: 580 mm Rim height: 43 mm Overall height: 200 mm Weight per pair: 180 kg Minimum width of tyres/chains: 300 mm Load capacity per pair with an axle distance of * 1000 mm: 6070 kg * 1500 mm: 7080 kg * 2000 mm: 8500 kg For a better understanding, the overall height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: overall height). Optionally, the heavy-duty ramps can be supplied with or without an edge; there is no price difference between the two variants. If the rails are designed without a border, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 300 mm! The ramp is secured with a chain (see pictures). This is placed on the bracket welded under the ramp and attached to a suitable fastening point on the vehicle. All heavy-duty ramps can be fitted with one of the support heads shown below – either the standard head (designation in the illustration: L), hook head (G), end head with tube (T) or end head with bearing (A).

Length 5462 mm Inner width: 500 mm Outer width: 580 mm Rim height: 43 mm Total height: 230 mm Weight per pair: 241 kg Minimum width of tyres/chains: 300 mm Load capacity per pair with an axle distance of * 1000 mm: 6670 kg * 1500 mm: 7500 kg * 2000 mm: 8570 kg For a better understanding, the overall height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: overall height). Optionally, the heavy-duty ramps can be supplied with or without an edge; there is no price difference between the two variants. If the rails are designed without a border, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 300 mm! The ramp is secured with a chain (see pictures). This is placed on the bracket welded under the ramp and attached to a suitable fastening point on the vehicle. All heavy-duty ramps can be fitted with one of the support heads shown below – either the standard head (designation in the illustration: L), hook head (G), end head with tube (T) or end head with bearing (A).

Length 2985 mm Inner width: 300 mm Outer width: 360 mm Rim height: 39.5 mm Total height: 125 mm Weight per pair: 52 kg Minimum tyre/track width: 200 mm Load capacity per pair with an axle distance of * 1000 mm: 3435 kg * 1500 mm: 4580 kg * 2000 mm: 6000 kg For a better understanding, the overall height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: overall height). Optionally, the heavy-duty ramp can be supplied with or without a lip; there is no price difference between the two variants. If the rails are designed without a lip, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 200 mm! The ramp is attached by means of an aluminium bracket (see picture) that can be hooked between the tail lift and the floor of a trailer. The clamp can be flexibly slid in and out under the ramp rail. Two plastic caps prevent the clamp from slipping out unintentionally. All heavy-duty ramps are available with one of the support heads shown below – either the standard head (designation in the figure: L), hook head (G), end head with tube (T) or end head with bearing (A).

Length 4500 mm Inner width: 340 mm Outer width: 400 mm Rim height: 41.5 mm Total height: 150 mm Weight per pair: 96 kg Minimum width of tyres/chains: 200 mm Load capacity per pair with an axle distance of * 1000 mm: 2945 kg * 1500 mm: 3435 kg * 2000 mm: 4120 kg For a better understanding, the total height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: total height). Optionally, the heavy-duty ramp can be supplied with or without a lip; there is no price difference between the two variants. If the rails are designed without a lip, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 200 mm! The ramp is attached by means of a universal steel bracket (see pictures), which can be hooked between the tail lift and the floor of a trailer. The bracket is attached to a crossbar under the ramp rail, can be moved sideways and is secured against slipping out; if necessary, it can be removed. For all heavy-duty ramps, one of the support heads shown below is available - either the standard head (designation in the figure: L), hook head (G), end head with tube (T) or end head with bearing (A).  

Length 2462 mm Inner width: 500 mm Outer width: 580 mm Rim height: 43 mm Total height: 230 mm Weight per pair: 111 kg Minimum width of tyres/chains: 300 mm Load capacity per pair with an axle distance of * 1000 mm: 16000 kg * 1500 mm: 16000 kg * 2000 mm: 16000 kg For a better understanding, the total height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: total height). Optionally, the heavy-duty ramp can be supplied with or without a rim; there is no price difference between the two variants. If the rails are designed without a rim, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 300 mm! The ramp is secured with a chain (see pictures). This is placed on the bracket welded under the ramp and attached to a suitable fastening point on the vehicle. All heavy-duty ramps can be fitted with one of the support heads shown below – either the standard head (designation in the illustration: L), hook head (G), end head with tube (T) or end head with bearing (A).  

Length 4495 mm Inner width: 240 mm Outer width: 300 mm Rim height: 29 mm Total height: 75 mm Weight per pair: 51 kg Minimum width of tyres/chains: 150 mm Load capacity per pair with an axle distance of * 1000 mm: 710 kg * 1250 mm: 770 kg * 1500 mm: 830 kg For a better understanding, the total height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: total height). Optionally, the heavy-duty ramp can be supplied with or without a lip; there is no price difference between the two variants. If the rails are designed without a lip, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 150 mm! The ramp is attached by means of an aluminium bracket (see picture) that can be hooked between the tail lift and the floor of a trailer. The clamp can be slid in and out under the ramp rail. It is secured against unintentional slipping out with two plastic caps. All heavy-duty ramps are available with one of the support heads shown below – either the standard head (designation in the figure: L), hook head (G), end head with tube (T) or end head with bearing (A).  

Length: 4485 mm Inner width: 300 mm Outer width: 360 mm Rim height: 39 mm Total height: 115 mm Weight per pair: 65 kg Minimum width of tyres/chains: 200 mm Load capacity per pair with an axle distance of * 1000 mm: 1285 kg * 1500 mm: 1500 kg * 2000 mm: 1800 kg For a better understanding, the total height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: total height). Optionally, the heavy-duty ramp can be supplied with or without a lip; there is no price difference between the two variants. If the rails are designed without a lip, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 200 mm! The ramp is attached by means of an aluminium bracket (see picture) that can be hooked between the tail lift and the floor of a trailer. The clamp can be flexibly slid in and out under the ramp rail. Two plastic caps prevent the clamp from slipping out unintentionally. All heavy-duty ramps are available with one of the support heads shown below – either the standard head (designation in the figure: L), hook head (G), end head with tube (T) or end head with bearing (A).

Length 3500 mm Inner width: 340 mm Outer width: 400 mm Ridge height: 41 mm Total height: 140 mm Weight per pair: 70 kg Minimum tyre/track width: 200 mm Load capacity per pair with an axle distance of * 1000 mm: 3325 kg * 1500 mm: 4155 kg * 2000 mm: 5540 kg For a better understanding, the overall height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: overall height). Optionally, the heavy-duty ramp can be ordered with or without a rim. The special price for this ramp model is only valid for the version with a rim, and the rimless version is subject to a surcharge. If the rails are designed without a rim, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 200 mm! The ramp is attached by means of a universal steel bracket (see pictures), which can be hooked between the tail lift and the floor of a trailer. The bracket is attached to a crossbar under the ramp rail, can be moved sideways and is secured against slipping out; if necessary, it can be removed. For all heavy-duty ramps, one of the support heads shown below is available - either the standard head (designation in the figure: L), hook head (G), end head with tube (T) or end head with bearing (A).

Length: 5462 mm Inner width: 450 mm Outer width: 510 mm Rim height: 43 mm Overall height: 185 mm Weight per pair: 172 kg Minimum tyre/track width: 200 mm Load capacity per pair with an axle distance of * 1000 mm: 3940 kg * 1500 mm: 4430 kg * 2000 mm: 5070 kg For a better understanding, the overall height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: overall height). Optionally, the heavy-duty ramps can be ordered with or without an edge; there is no price difference between the two variants. If the rails are designed without a border, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 200 mm! The ramp is secured with a chain (see pictures). This is placed on the bracket welded under the ramp and attached to a suitable fastening point on the vehicle. All heavy-duty ramps can be fitted with one of the support heads shown below – either the standard head (designation in the figure: L), hook head (G), end head with tube (T) or end head with bearing (A).

Length 3495 mm Inner width: 240 mm Outer width: 300 mm Rim height: 29 mm Total height: 75 mm Weight per pair: 45 kg Minimum tyre/track width: 150 mm Load capacity per pair with an axle distance of * 1000 mm: 1400 kg * 1250 mm: 1550 kg * 1500 mm: 1750 kg For a better understanding, the overall height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: overall height). Optionally, the heavy-duty ramp can be supplied with or without a lip; there is no price difference between the two variants. If the rails are designed without a lip, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 150 mm! The ramp is attached by means of an aluminium bracket (see picture) that can be hooked between the tail lift and the floor of a trailer. The clamp can be flexibly pushed in and out sideways under the ramp rail. The clamp is secured against unintentional slipping out with two plastic caps. All heavy-duty ramps are available with one of the support heads shown below – either the standard head (designation in the figure: L), hook head (G), end head with tube (T) or end head with bearing (A).

Length 3000 mm Inner width: 400 mm Outer width: 460 mm Rim height: 41 mm Total height: 140 mm Weight per pair: 71 kg Minimum width of tyres/tracks: 200 mm Load capacity per pair with an axle distance of * 1000 mm: 4155 kg * 1500 mm: 5540 kg * 2000 mm: 7000 kg For a better understanding, the total height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: total height). Optionally, the heavy-duty ramp can be supplied with or without a lip; there is no price difference between the two variants. If the rails are designed without a lip, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 200 mm! The ramp is attached by means of a universal steel bracket (see pictures), which can be hooked between the tail lift and the floor of a trailer. The bracket is attached to a crossbar under the ramp rail, can be moved sideways and is secured against slipping out; if necessary, it can be removed. For all heavy-duty ramps, one of the support heads shown below is available - either the standard head (designation in the figure: L), hook head (G), end head with tube (T) or end head with bearing (A).

Length: 1995 mm Inner width: 440 mm Outer width: 500 mm Rim height: 29 mm Total height: 65 mm Weight per pair: 30 kg Minimum width of tyres/chains: 300 mm Load capacity per pair with an axle distance of * 1000 mm: 2000 kg * 1250 mm: 2450 kg * 1500 mm: 2450 kg For a better understanding, the total height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: total height). Optionally, the heavy-duty ramp can be supplied with or without a lip; there is no price difference between the two variants. If the rails are designed without a lip, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 300 mm! The ramp is attached by means of an aluminium bracket (see picture), which can be hooked between the tail lift and the floor of a trailer. The clamp can be slid in and out under the ramp rail. It is secured against unintentional slipping out with two plastic caps. All heavy-duty ramps are available with one of the support heads shown below – either the standard head (designation in the figure: L), hook head (G), end head with tube (T) or end head with bearing (A).

Length 5000 mm Inner width: 340 mm Outer width: 400 mm Rim height: 41.5 mm Total height: 150 mm Weight per pair: 107 kg Minimum width of tyres/chains: 200 mm Load capacity per pair with an axle distance of * 1000 mm: 2575 kg * 1500 mm: 2945 kg * 2000 mm: 3435 kg For a better understanding, the total height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: total height). Optionally, the heavy-duty ramp can be supplied with or without a lip; there is no price difference between the two variants. If the rails are designed without a lip, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 200 mm! The ramp is attached by means of a universal steel bracket (see pictures), which can be hooked between the tail lift and the floor of a trailer. The bracket is attached to a crossbar under the ramp rail, can be moved sideways and is secured against slipping out; if necessary, it can be removed. For all heavy-duty ramps, one of the support heads shown below is available - either the standard head (designation in the figure: L), hook head (G), end head with tube (T) or end head with bearing (A).

Length 3995 mm Inner width: 240 mm Outer width: 300 mm Rim height: 29 mm Total height: 75 mm Weight per pair: 51 kg Minimum width of tyres/chains: 150 mm Load capacity per pair with an axle distance of * 1000 mm: 1160 kg * 1250 mm: 1270 kg * 1500 mm: 1400 kg For a better understanding, the total height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: total height). Optionally, the heavy-duty ramp can be supplied with or without a lip; there is no price difference between the two variants. If the rails are designed without a lip, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 150 mm! The ramp is attached by means of an aluminium bracket (see picture) that can be hooked between the tail lift and the floor of a trailer. The clamp can be slid in and out under the ramp rail. It is secured against unintentional slipping out with two plastic caps. All heavy-duty ramps are available with one of the support heads shown below – either the standard head (designation in the figure: L), hook head (G), end head with tube (T) or end head with bearing (A).