Length 4495 mm Inner width: 340 mm Outer width: 400 mm Rim height: 29 mm Total height: 100 mm Weight per pair: 60 kg Minimum width of tyres/chains: 200 mm Load capacity per pair with an axle distance of * 1000 mm: 1070 kg * 1250 mm: 1160 kg * 1500 mm: 1250 kg For a better understanding, the total height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: total height). Optionally, the heavy-duty ramp can be supplied with or without a lip; there is no price difference between the two variants. If the rails are designed without a lip, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 300 mm! The ramp is attached by means of an aluminium bracket (see picture) that can be hooked between the tail lift and the floor of a trailer. The clamp can be flexibly pushed in and out under the ramp rail. It is secured against unintentional slipping out with two plastic caps. All heavy-duty ramps are available with one of the support heads shown below – either the standard head (designation in the figure: L), hook head (G), end head with tube (T) or end head with bearing (A).

Length 3495 mm Inner width: 340 mm Outer width: 400 mm Rim height: 29 mm Total height: 100 mm Weight per pair: 47 kg Minimum width of tyres/chains: 200 mm Load capacity per pair with an axle distance of * 1000 mm: 1500 kg * 1250 mm: 1680 kg * 1500 mm: 1900 kg For a better understanding, the total height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: total height). Optionally, the heavy-duty ramp can be supplied with or without a lip; there is no price difference between the two variants. If the rails are designed without a lip, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 300 mm! The ramp is attached by means of an aluminium bracket (see picture) that can be hooked between the tail lift and the floor of a trailer. The clamp can be flexibly pushed in and out under the ramp rail. It is secured against unintentional slipping out with two plastic caps. All heavy-duty ramps are available with one of the support heads shown below – either the standard head (designation in the figure: L), hook head (G), end head with tube (T) or end head with bearing (A).

Length 4995 mm Inner width: 340 mm Outer width: 400 mm Rim height: 29 mm Total height: 100 mm Weight per pair: 66 kg Minimum tyre/track width: 200 mm Load capacity per pair with an axle distance of * 1000 mm: 940 kg * 1250 mm: 1000 kg * 1500 mm: 1070 kg For a better understanding, the total height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: total height). Optionally, the heavy-duty ramp can be supplied with or without a lip; there is no price difference between the two variants. If the rails are designed without a lip, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 300 mm! The ramp is attached by means of an aluminium bracket (see picture) that can be hooked between the tail lift and the floor of a trailer. The clamp can be flexibly pushed in and out under the ramp rail. It is secured against unintentional slipping out with two plastic caps. All heavy-duty ramps are available with one of the support heads shown below – either the standard head (designation in the figure: L), hook head (G), end head with tube (T) or end head with bearing (A).  

Length 2495 mm Inner width: 340 mm Outer width: 400 mm Rim height: 29 mm Total height: 100 mm Weight per pair: 38 kg Minimum width of tyres/tracks: 200 mm Load capacity per pair with an axle distance of * 1000 mm: 2495 kg * 1250 mm: 2444 kg * 1500 mm: 2346 kg For a better understanding, the total height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: total height). Optionally, the heavy-duty ramp can be supplied with or without a lip; there is no price difference between the two variants. If the rails are designed without a lip, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 300 mm! The ramp is attached by means of an aluminium bracket (see picture) that can be hooked between the tail lift and the floor of a trailer. The clamp can be flexibly pushed in and out under the ramp rail. It is secured against unintentional slipping out with two plastic caps. All heavy-duty ramps are available with one of the support heads shown below – either the standard head (designation in the figure: L), hook head (G), end head with tube (T) or end head with bearing (A).

Length 3995 mm Inner width: 340 mm Outer width: 400 mm Rim height: 29 mm Total height: 100 mm Weight per pair: 54 kg Minimum tyre/track width: 200 mm Load capacity per pair with an axle distance of * 1000 mm: 1250 kg * 1250 mm: 1370 kg * 1500 mm: 1500 kg For a better understanding, the total height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: total height). Optionally, the heavy-duty ramp can be supplied with or without a lip; there is no price difference between the two variants. If the rails are designed without a lip, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 300 mm! The ramp is attached by means of an aluminium bracket (see picture) that can be hooked between the tail lift and the floor of a trailer. The clamp can be flexibly pushed in and out under the ramp rail. It is secured against unintentional slipping out with two plastic caps. All heavy-duty ramps are available with one of the support heads shown below – either the standard head (designation in the figure: L), hook head (G), end head with tube (T) or end head with bearing (A).

Length 2995 mm Inner width: 340 mm Outer width: 400 mm Rim height: 29 mm Total height: 100 mm Weight per pair: 45 kg Minimum width of tyres/tracks: 200 mm Load capacity per pair with an axle distance of * 1000 mm: 1900 kg * 1250 mm: 2150 kg * 1500 mm: 2500 kg For a better understanding, the total height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: total height). Optionally, the heavy-duty ramp can be supplied with or without a lip; there is no price difference between the two variants. If the rails are designed without a lip, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 300 mm! The ramp is attached by means of an aluminium bracket (see picture), which can be hooked between the tail lift and the floor of a trailer. The clamp can be slid in and out under the ramp rail. It is secured against unintentional slipping out with two plastic caps. All heavy-duty ramps are available with one of the support heads shown below – either the standard head (designation in the figure: L), hook head (G), end head with tube (T) or end head with bearing (A).