Length: 4462 mm Inner width: 450 mm Outer width: 510 mm Rim height: 43 mm Total height: 185 mm Weight per pair: 142 kg Minimum tyre/track width: 200 mm Load capacity per pair with an axle distance of * 1000 mm: 5070 kg * 1500 mm: 5910 kg * 2000 mm: 7100 kg For a better understanding, the overall height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: overall height). Optionally, the heavy-duty ramp can be ordered with or without a rim. The special price for this ramp model is only valid for the version with a rim, and the rimless version is subject to a surcharge. If the rails are designed without a rim, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 200 mm! The ramp is secured with a chain (see pictures). This is placed on the bracket welded under the ramp and attached to a suitable fastening point on the vehicle. All heavy-duty ramps can be fitted with one of the support heads shown below – either the standard head (designation in the illustration: L), hook head (G), end head with tube (T) or end head with bearing (A).

Length: 5462 mm Inner width: 450 mm Outer width: 510 mm Rim height: 43 mm Overall height: 185 mm Weight per pair: 172 kg Minimum tyre/track width: 200 mm Load capacity per pair with an axle distance of * 1000 mm: 3940 kg * 1500 mm: 4430 kg * 2000 mm: 5070 kg For a better understanding, the overall height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: overall height). Optionally, the heavy-duty ramps can be ordered with or without an edge; there is no price difference between the two variants. If the rails are designed without a border, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 200 mm! The ramp is secured with a chain (see pictures). This is placed on the bracket welded under the ramp and attached to a suitable fastening point on the vehicle. All heavy-duty ramps can be fitted with one of the support heads shown below – either the standard head (designation in the figure: L), hook head (G), end head with tube (T) or end head with bearing (A).

Length: 4962 mm Inner width: 450 mm Outer width: 510 mm Rim height: 43 mm Overall height: 185 mm Weight per pair: 157 kg Minimum tyre/track width: 200 mm Load capacity per pair with an axle distance of * 1000 mm: 4430 kg * 1500 mm: 5070 kg * 2000 mm: 5910 kg For a better understanding, the total height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: total height). Optionally, the heavy-duty ramps can be ordered with or without an edge; there is no price difference between the two variants. If the rails are designed without a border, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 200 mm! The ramp is secured with a chain (see pictures). This is placed on the bracket welded under the ramp and attached to a suitable fastening point on the vehicle. All heavy-duty ramps can be fitted with one of the support heads shown below – either the standard head (designation in the figure: L), hook head (G), end head with tube (T) or end head with bearing (A).

Length: 2962 mm Inner width: 450 mm Outer width: 510 mm Rim height: 43 mm Total height: 185 mm Weight per pair: 105 kg Minimum width of tyres/chains: 200 mm Load capacity per pair with an axle distance of * 1000 mm: 8870 kg * 1500 mm: 12000 kg * 2000 mm: 12000 kg For a better understanding, the total height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: total height). Optionally, the heavy-duty ramp can be supplied with or without a rim; there is no price difference between the two variants. If the rails are designed without a rim, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 200 mm! The ramp is secured with a chain (see pictures). This is placed on the bracket welded under the ramp and attached to a suitable fastening point on the vehicle. All heavy-duty ramps can be fitted with one of the support heads shown below – either the standard head (designation in the illustration: L), hook head (G), end head with tube (T) or end head with bearing (A).  

Length: 3962 mm Inner width: 450 mm Outer width: 510 mm Rim height: 43 mm Overall height: 185 mm Weight per pair: 127 kg Minimum tyre/track width: 200 mm Load capacity per pair with an axle distance of * 1000 mm: 5910 kg * 1500 mm: 7100 kg * 2000 mm: 8870 kg For a better understanding, the overall height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: overall height). Optionally, the heavy-duty ramps can be supplied with or without an edge; there is no price difference between the two variants. If the rails are designed without a border, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 200 mm! The ramp is secured with a chain (see pictures). This is placed on the bracket welded under the ramp and attached to a suitable fastening point on the vehicle. All heavy-duty ramps can be fitted with one of the support heads shown below – either the standard head (designation in the figure: L), hook head (G), end head with tube (T) or end head with bearing (A).

Length: 3462 mm Inner width: 450 mm Outer width: 510 mm Rim height: 43 mm Total height: 185 mm Weight per pair: 122 kg Minimum width of tyres/chains: 200 mm Load capacity per pair with an axle distance of * 1000 mm: 7100 kg * 1500 mm: 8870 kg * 2000 mm: 12000 kg For a better understanding, the overall height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: overall height). Optionally, the heavy-duty ramps can be ordered with or without an edge; there is no price difference between the two variants. If the rails are designed without a border, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 200 mm! The ramp is secured with a chain (see pictures). This is placed on the bracket welded under the ramp and attached to a suitable fastening point on the vehicle. All heavy-duty ramps can be fitted with one of the support heads shown below – either the standard head (designation in the figure: L), hook head (G), end head with tube (T) or end head with bearing (A).

Length: 2462 mm Inner width: 450 mm Outer width: 510 mm Rim height: 43 mm Overall height: 185 mm Weight per pair: 88 kg Minimum width of tyres/tracks: 200 mm Load capacity per pair with an axle distance of * 1000 mm: 12000 kg * 1500 mm: 12000 kg * 2000 mm: 12000 kg For a better understanding, the total height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: total height). Optionally, the heavy-duty ramps can be designed with or without an edge; there is no price difference between the two variants. If the rails are designed without a border, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 200 mm! The ramp is secured with a chain (see pictures). This is placed on the bracket welded under the ramp and attached to a suitable fastening point on the vehicle. All heavy-duty ramps can be fitted with one of the support heads shown below – either the standard head (designation in the figure: L), hook head (G), end head with tube (T) or end head with bearing (A).