Length 4495 mm Inner width: 240 mm Outer width: 300 mm Rim height: 29 mm Total height: 75 mm Weight per pair: 51 kg Minimum width of tyres/chains: 150 mm Load capacity per pair with an axle distance of * 1000 mm: 710 kg * 1250 mm: 770 kg * 1500 mm: 830 kg For a better understanding, the total height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: total height). Optionally, the heavy-duty ramp can be supplied with or without a lip; there is no price difference between the two variants. If the rails are designed without a lip, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 150 mm! The ramp is attached by means of an aluminium bracket (see picture) that can be hooked between the tail lift and the floor of a trailer. The clamp can be slid in and out under the ramp rail. It is secured against unintentional slipping out with two plastic caps. All heavy-duty ramps are available with one of the support heads shown below – either the standard head (designation in the figure: L), hook head (G), end head with tube (T) or end head with bearing (A).  

Length 1995 mm Inner width: 240 mm Outer width: 300 mm Rim height: 29 mm Total height: 75 mm Weight per pair: 24 kg Minimum tyre/track width: 150 mm Load capacity per pair with an axle distance of * 1000 mm: 2510 kg * 1250 mm: 3000 kg * 1500 mm: 3300 kg For a better understanding, the total height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: total height). Optionally, the heavy-duty ramp can be supplied with or without a lip; there is no price difference between the two variants. If the rails are designed without a lip, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 150 mm! The ramp is attached by means of an aluminium bracket (see picture) that can be hooked between the tail lift and the floor of a trailer. The clamp can be flexibly pushed in and out sideways under the ramp rail. The clamp is secured against unintentional slipping out with two plastic caps. All heavy-duty ramps are available with one of the support heads shown below – either the standard head (designation in the figure: L), hook head (G), end head with tube (T) or end head with bearing (A).

Length 3995 mm Inner width: 240 mm Outer width: 300 mm Rim height: 29 mm Total height: 75 mm Weight per pair: 45 kg Minimum tyre/track width: 150 mm Load capacity per pair with an axle distance of * 1000 mm: 830 kg * 1250 mm: 910 kg * 1500 mm: 1000 kg For a better understanding, the total height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: total height). Optionally, the heavy-duty ramp can be supplied with or without a lip; there is no price difference between the two variants. If the rails are designed without a lip, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 150 mm! The ramp is attached by means of an aluminium bracket (see picture) that can be hooked between the tail lift and the floor of a trailer. The clamp can be slid in and out under the ramp rail. It is secured against unintentional slipping out with two plastic caps. All heavy-duty ramps are available with one of the support heads shown below – either the standard head (designation in the figure: L), hook head (G), end head with tube (T) or end head with bearing (A).  

Length 2495 mm Inner width: 240 mm Outer width: 300 mm Rim height: 29 mm Total height: 75 mm Weight per pair: 29 kg Minimum width of tyres/tracks: 150 mm Load capacity per pair with an axle distance of * 1000 mm: 1670 kg * 1250 mm: 2010 kg * 1500 mm: 2510 kg For a better understanding, the overall height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: overall height). Optionally, the heavy-duty ramp can be supplied with or without a lip; there is no price difference between the two variants. If the rails are designed without a lip, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 150 mm! The ramp is attached by means of an aluminium bracket (see picture) that can be hooked between the tail lift and the floor of a trailer. The clamp can be slid in and out under the ramp rail. It is secured against unintentional slipping out with two plastic caps. All heavy-duty ramps are available with one of the support heads shown below – either the standard head (designation in the figure: L), hook head (G), end head with tube (T) or end head with bearing (A).

Length 3495 mm Inner width: 240 mm Outer width: 300 mm Rim height: 29 mm Total height: 75 mm Weight per pair: 40 kg Minimum tyre/track width: 150 mm Load capacity per pair with an axle distance of * 1000 mm: 1000 kg * 1250 mm: 1110 kg * 1500 mm: 1250 kg For a better understanding, the total height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: total height). Optionally, the heavy-duty ramp can be supplied with or without a lip; there is no price difference between the two variants. If the rails are designed without a lip, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 150 mm! The ramp is attached by means of an aluminium bracket (see picture) that can be hooked between the tail lift and the floor of a trailer. The clamp can be slid in and out under the ramp rail. It is secured against unintentional slipping out with two plastic caps. All heavy-duty ramps are available with one of the support heads shown below – either the standard head (designation in the figure: L), hook head (G), end head with tube (T) or end head with bearing (A).

Length 2995 mm Inner width: 240 mm Outer width: 300 mm Rim height: 29 mm Total height: 75 mm Weight per pair: 34 kg Minimum width of tyres/chains: 150 mm Load capacity per pair with an axle distance of * 1000 mm: 1250 kg * 1250 mm: 1430 kg * 1500 mm: 1670 kg For a better understanding, the overall height, edge height, outer and inner width are shown in the sketch (value A: inner width, value B: outer width, value C: edge height, value D: overall height). Optionally, the heavy-duty ramp can be supplied with or without a lip; there is no price difference between the two variants. If the rails are designed without a lip, the corrugated surface is welded flush with the upper edge of the side profiles during ramp production. Please note that the tyres or chains of the vehicle driving onto the ramp must have a minimum width of 150 mm! The ramp is attached by means of an aluminium bracket (see picture) that can be hooked between the tail lift and the floor of a trailer. The clamp can be flexibly pushed in and out sideways under the ramp rail. The clamp is secured against unintentional slipping out with two plastic caps. All heavy-duty ramps are available with one of the support heads shown below – either the standard head (designation in the figure: L), hook head (G), end head with tube (T) or end head with bearing (A).