Quickly build a safe staircase
The slots allow for a stair inclination of 35° to 50°. The optimum inclination is 38° with a rise of 191 mm in conjunction with the safety treads with a tread depth of 275 mm. Select the basic elements of the E-steel stair system components using the item numbers from the adjacent drawing and add your favourite railing design.
1 - Foot section, right
2 - Foot section, left
3 - Stair stringer - fvz. 4,030 mm (right) - 13 steps
4 - Stair stringer - fvz. 4,030 mm (right) - 13 steps
4b - Sliding fitting ‘UNI’-left
4c - ‘UNI’ sliding fitting, right
6 - 45° angle bracket fitting, adjustment range 35°-50°
7 - angle iron bracket, length 2,000 mm
9 - wall bracket for wall mounting
10 - banister post, complete
10 - banister post for V2A handrail
12 - Handrail 6 metres Ø42.2 mm (hot-dip galvanised)
12 - Handrail 6 metres Ø42.2 mm - V2A grain 240
180° pipe connector made of polyamide (PA) 6, reinforced with 30% glass fibre or glass beads. Colour: black Suitable for round tube, 42.4 mm outer dimension (wall thickness 3.20 mm), with steel core Packaging unit: 1 tube connector
This 45° angle fitting is primarily used to connect the stair stringer to the stair landing. The angle fitting is made of steel (material ST37) and is hot-dip galvanised.
Hot-dip galvanised steel angle bracket (material ST37) with pre-punched slotted holes. The angle iron support with its slotted holes is matched to the quick-assembly stair stringers and serves as a support surface for the landing. Length: 2000 mm
Filler rod made of steel (material ST37) hot-dip galvanised in a full bath Diameter: 10 mm Length: 2000 mm Cut edges must be cold galvanised using zinc paste/zinc spray.
Solid end piece for wall or floor mounting. These base pieces are used at the bottom as well as at the top of rapid staircases to maximise the stability of the staircase. The base piece is made of steel (material ST37) and is fully hot-dip galvanised.
Solid end piece for wall or floor mounting. These base pieces are used at the bottom as well as at the top of rapid staircases to maximise the stability of the staircase. The base piece is made of steel (material ST37) and is fully hot-dip galvanised.
Handrail tube made of steel (material ST37) hot-dip galvanised in a full bath Diameter: 42.4 mm Length: 2000 mm Cut edges must be cold galvanised using zinc paste/zinc spray.
The E-steel balusters are perfectly matched to the quick-assembly system and can be installed in just a few simple steps. It is firmly clamped to the stair stringer without having to drill new holes. The quick-assembly balusters are made of steel (material ST37) and hot-dip galvanised. The handrail retaining ring is made of stainless steel V2A, material 1.4301 and can accommodate a handrail Ø 42.4 mm. Up to 7 10 mm Ø filler rods can be screwed to the railing post. This ensures maximum safety and flexibility. The individual stair inclination of 35°-55° degrees is fully maintained with this railing. Total height: approx. 1265 mm Clearance between the filler bars: 87 mm
Quick-assembly stair stringer made of steel (material ST37) with slotted holes for perforated plate treads. The stair stringer is made of 3 mm steel and is hot-dip galvanised. The 4030 mm long stair stringer is ideal for designing staircase systems. Thanks to the pre-punched oblong holes, this stringer can be used for a staircase inclination angle of 35°-55° and can accommodate a maximum of 13 perforated plate treads. The contractor / staircase installer is responsible for the structural verification of the staircase.
Quick-assembly stair stringer made of steel (material ST37) with slotted holes for grating steps. The stair stringer is made of 3 mm steel and is hot-dip galvanised. The 4030 mm long stair stringer is ideal for designing staircase systems. Thanks to the pre-punched oblong holes, this stringer can be used for a staircase inclination angle of 35°-55° and can accommodate a maximum of 13 grating treads. The contractor / staircase installer is responsible for the structural verification of the staircase.
Hot-dip galvanised bolt with nut (molybdenum disulphide coated) and two hot-dip galvanised washers. The hot-dip galvanised items are the profile solution to the galvanised screws. These have a significantly thicker zinc coating of approx. 50 - 80 µ.
Colour: grey Height: 30mm Diameter: 42.4 mm Material thickness: 1 mm
Quick-assembly stair stringer made of steel (material ST37) with slotted holes for grating steps. The stair stringer is made of 3 mm steel and is hot-dip galvanised. The 4030 mm long stair stringer is ideal for designing staircase systems. Thanks to the pre-punched oblong holes, this stringer can be used for a staircase inclination angle of 35°-55° and can accommodate a maximum of 13 grating treads. The contractor / staircase installer is responsible for the structural verification of the staircase.
Quick-assembly stair stringer made of steel (material ST37) with slotted holes for perforated plate treads. The stair stringer is made of 3 mm steel and is hot-dip galvanised. The 4030 mm long stair stringer is ideal for designing staircase systems. Thanks to the pre-punched oblong holes, this stringer can be used for a staircase inclination angle of 35°-55° and can accommodate a maximum of 13 perforated plate treads. The contractor / staircase installer is responsible for the structural verification of the staircase.
Hot-dip galvanised sliding fitting for extending the left-hand grating or perforated plate stair stringer. Length: 560 mm Width: 150 mm Height: 41 mm Material thickness: 3 mm
Hot-dip galvanised sliding fitting for extending the right-hand grating or perforated plate stair stringer. Length: 560 mm Width: 150 mm Height: 41 mm Material thickness: 3 mm
Material 1.4301, grain 240 ground Diameter: 42.4 mm Length: 2000 mm
AISI 304 - grain 240 ground for hammering in, hollow inside Tube diameter: 42.4 x 2.0 mm Weight approx. 0.08 kg
Wall fitting made of steel and hot-dip galvanised in a full bath. The individual stair inclination of 35° - 55° is also fully retained with this Fitting.